News:

Welcome ZX10R Ninja Owners!!!!!
Front Page Here
Can all new members that haven't posted please read the admin and announcement page for the forum rules.

Main Menu

venture shield

Started by topher454, August 31, 2008, 09:24:10 PM

Previous topic - Next topic

topher454

as a few of you know my bikes in at the moment for a new paint job

trying to find a way of preventing stone chips  :crybaby2:

checked on venture shield but feel its over priced for a relatively small kit

just wondered if any1's aware of a more econimical alternative

thanx guys  :icon_thumleft:

oh....and gals  :hello2:  lol

bike will be fin for nxt wkend......heres hoping we av some decent weather   [wall]  [wall]  [wall]

truescot

Quote from: topher454 on August 31, 2008, 09:24:10 PM
trying to find a way of preventing stone chips  :crybaby2:


I doubt it would be cheap, easy or practical but you could try that polyeurathane coating they put on dance floors that they claim it takes a diamond to scratch, could be handy in an off too :)

Chrisblack10r

i have the venture shield fitted to my 08

would easily get it again if i had too


Volkswagen Master Technician with an 08 zx10r with 181.4 BHP at the back wheel hahaha!!!!!

mrwippy

 u could try a thick clear sticky back plastic  :roll:
www.geedesigns.weebly.com
www.bunnypenny.com

tony83

//http//: [insert/quote/here]

NinjaPaul

Quote from: Chrisblack10r on August 31, 2008, 09:46:25 PM
i have the venture shield fitted to my 08

would easily get it again if i had too

ditto

bladeblaster

leave it in the garage, save a fortune on petrol too............. :roll:
I have seen the light, and it is BLACK!!!!!

madlad

Motografix in Doncaster do the number boards for the front of the bike

I know a lot of people use them to prevent or even hide stone chips.  :icon_thumleft:
Has anyone seen my marbles?

drewk8

i got venture shield kit on mine. worth every penny. 2 thousand miles and not a mark on her.. got mine through dealer via a company called covertech west midlands.
think the whole bike kit was about £90 and fitted it myself. only bits i didnt put on were the ones on the rear panels by passenger seat area.

10rmish

go toa craft shop and get some clear plasic on a roll for a couple of quid.it does the same job.

NinjaPaul

Quote from: 10rmish on September 09, 2008, 02:28:18 PM
go toa craft shop and get some clear plasic on a roll for a couple of quid.it does the same job.

Not quite, the venture shield film goes on virtually invisible if fitted correctly and can be removed and refitted as many times as you like.

Sticky back plastic is a pain in the arse to fit as it does not conform around complex curved shapes like ventureshield does. It also has a tendency to leave highly visible air bubbles which are very difficult to get rid of. Sticky back plastic cannot be reused and will leave a horrible sticky residue behind when removed.

Cheap, yes

As good as, not even close. B-)

topher454

made mind up 4 me guys

invested quite a bit in this paint job

so gona splash out on venture shield  :icon_thumright:

Old Son

Does anybody have a link to a video of Venture shield being applied? I've got to do mine in a couple of weeks. Should I wax the bodywork first to make sure it is clean? Thanks

jamma10566

Always stay in front! Let your mates get the chips. Look forward to seeing the pics of the paintjob. If its not done yet, you could always ask them to put some plasticiser in the lacquer. It wont stop chips completely but will minimise it. Alot of car manufacturers do this now. Ever noticed how a resprayed bonnet seems to chip easier than original paint.
Sponsor me please, its a very good cause.
http://www.justgiving.com/James-CoryTakesabullet

geemonster

Look on ebay mate. I only brought some for my back plastics where the passenger boots rub and got crap loads for £12 quid. Just need to look a little for it.