News:

Welcome ZX10R Ninja Owners!!!!!
Front Page Here
Can all new members that haven't posted please read the admin and announcement page for the forum rules.

Main Menu

09 modification help !!

Started by Gav179, May 19, 2010, 10:38:18 PM

Previous topic - Next topic

Gav179

Hello all

I got a dilema thats been bugging me since i got my 09 white zx10r in october 2009

I want to modify the  standard end can because its dam ugly, but  at the minute i cant stretch to the cost of a new pipe coz the insurance is due, a new baby as arrived and im now skint  :emb: i was hoping you could tell me if it would be ok to either spray the can black or anthracite or cover it with faux carbon fibre that just sticks on like your local sign place would do or would it look total crap, i thought if i made it darker it wouldnt stand out as much, eventually im gonna get the Akrapovic carbon slip on.

Any help on tarting up the standard end can would be greatly appreciated, also would the 2009/2010 ZX6R end can work or would it cause issues :iamwithstupid:, the racefit  cans look smaller than the ZX6R can thats why im wonderin as its a tidy looking can.

A mod you can do on the 2008/2009/2010  models is remove the little black container thats just behind the lights thats attached to the bottom of the air intake duct then silicone a rubber gromit over the remaining hole to stop air leakage and this gives you the full roar of the direct ram air system giving your bike a more beefy sound as your accelerating, i got this mod off ZX10R.net

Thanks for your help

Chrisblack10r

Quote from: Gav179 on May 19, 2010, 10:38:18 PM
Hello all

I got a dilema thats been bugging me since i got my 09 white zx10r in october 2009

I want to modify the  standard end can because its dam ugly, but  at the minute i cant stretch to the cost of a new pipe coz the insurance is due, a new baby as arrived and im now skint  :emb: i was hoping you could tell me if it would be ok to either spray the can black or anthracite or cover it with faux carbon fibre that just sticks on like your local sign place would do or would it look total crap, i thought if i made it darker it wouldnt stand out as much, eventually im gonna get the Akrapovic carbon slip on.

Any help on tarting up the standard end can would be greatly appreciated, also would the 2009/2010 ZX6R end can work or would it cause issues :iamwithstupid:, the racefit  cans look smaller than the ZX6R can thats why im wonderin as its a tidy looking can.

A mod you can do on the 2008/2009/2010  models is remove the little black container thats just behind the lights thats attached to the bottom of the air intake duct then silicone a rubber gromit over the remaining hole to stop air leakage and this gives you the full roar of the direct ram air system giving your bike a more beefy sound as your accelerating, i got this mod off ZX10R.net

Thanks for your help

isnt the little black box a water drain for moisture that is pulled into the air intake system?


Volkswagen Master Technician with an 08 zx10r with 181.4 BHP at the back wheel hahaha!!!!!

Gav179

Not sure wot it's for, I looked it up in the workshop and it's doesn't say, as I don't ride my 10 in the rain it shouldn't be a problem, should it ? :icon_scratch: I re checked zx10r.net and there's no horror stories bout it there and as the hole is only in the middle moisture would still pass it anyway, I posted it here to find out if it was ok or not so thanks for your input I think I will ask at a Kawasaki dealership wot the containers actually for

stevo_nwuk

A K&N air filter would give you more intake noise if that's what you are after.

Gav179

Hi stevo
if i was to put a k&n on or a pipercross filter would i have to have the bike fueling set up on a dyno or would it just run fine, this is my 1st zx10r and im listening and learning bout the big kawasaki

andicog

No reason why you cant paint the end can, you could use Sperex satin or as I have on my old slingshot engine, normal basecoat and 2 pack clear, make sure you give it a light key up using a grey scotchbrite pad or similar and give it a light coat of primer to aid adhesion (only needs a see through coat). I think the can will get too warm for fake carbon as the heat seems to soften the adhesive.  ;-)
Age And Treachery Shall Always Triumph Over Youth And Skill . . . . . . .

Gav179

Andicog, cheers mate this was the kind of answer I was looking for, I was thinking of going for a matt black finish if that's posible or would I need the clear lacquer (think that's how ya spell it) to keep the paint on there

Charlie

I would be very wary of putting conventional primer on an exhaust.

A mate of mine did that....then sprayed stain black heat dispersant paint over the top. It lasted about 2 days until it had burned off in big chunks.

An exhaust will get much hotter than an engine crankcase. You need proper heat resistant or heat dispersant paint and NO primer underneath.
Refugee admin from www.gixerjunkies.com

drewk8

you should be able to get vht paint in spray form still? used to use it years ago on mini exhausts back in my youthful days :pottytrain2:

stevo_nwuk

Quote from: Gav179 on May 20, 2010, 01:22:37 PM
Hi stevo
if i was to put a k&n on or a pipercross filter would i have to have the bike fueling set up on a dyno or would it just run fine, this is my 1st zx10r and im listening and learning bout the big kawasaki
Would run ok, if that was the only mod.

docta13

have a look at ebay at a company called mtc they arent that much money i only paid 135 and it looks and sounds the nutz, surley if u ever sold the bike on woudnt you rather give the standard exhaust back untouched???  i only say this as thats how i would like it..
i started out with nothing and i still got most of it left!

Gav179

yeah i know wot you mean doc but i did all that with my k7 gixxer 750 and when i traded it in for my zx10r the dealer wasnt fussed whether it was standard or not he was offering the same money so i removed the screen the recovered seat and the tail tidy to sell on i left the braided hoses on as you would and im still stuck with the R&G tail tidy, sometimes its not worth the hassle keeping the trick bits unless its a power commander or carbon wheels or summit, you got me thinkin tho £135 is a bargain for any end can :icon_thumright:

andicog

Quote from: Gav179 on May 21, 2010, 01:39:25 AM
Andicog, cheers mate this was the kind of answer I was looking for, I was thinking of going for a matt black finish if that's posible or would I need the clear lacquer (think that's how ya spell it) to keep the paint on there

If you want matt black then just use Sperex VHT or similar, no need for  clear coat (I cant spell lacquer either . . . )   :icon_thumright:
Age And Treachery Shall Always Triumph Over Youth And Skill . . . . . . .

andicog

Quote from: Charlie on May 21, 2010, 06:34:14 AM
I would be very wary of putting conventional primer on an exhaust.

A mate of mine did that....then sprayed stain black heat dispersant paint over the top. It lasted about 2 days until it had burned off in big chunks.

An exhaust will get much hotter than an engine crankcase. You need proper heat resistant or heat dispersant paint and NO primer underneath.

I would agree with you that the exhaust obviously gets hotter than crankcases and even hotter than the head area, we are talking about a silencer and I'm sure there would be no problem, if heated uniformly 2 pack paint and standard base coat will take enough heat to fry an egg on the surface. how hot do you recon a black car roof gets in Saudi heat ?   Sperex actually used to recommend cellulose  primer under their VHT engine paint when applying over bare metal.  Here's my gixer engine, done 4 years ago with half coat of aerosol primer, basecoat and 2 pack clear, still perfect even around the exhaust ports. If using Sperex and its not over bare metal there is no need for primer anyway, quick key up and (as Brian Cant used to say . . )  spray away !  :lol:


Age And Treachery Shall Always Triumph Over Youth And Skill . . . . . . .

Gav179

Nice work andicog that engine looks trick mate :icon_thumright: