Have sorted problem:
(http://i136.photobucket.com/albums/q171/horse_ZX10R/1e35_1_b.jpg)
Have just bought, no blocked injectors are going to beat me [rofl] only need injectors so if anybody needs spares you know where I am!!!
glad to see you bought em fella :icon_thumright:
ya wally [whistle]
Quote from: GRNINJA on March 23, 2008, 12:29:57 PM
ya wally [whistle]
It wasn't my fault (http://bestsmileys.com/big/2.gif)
not what I heard [whistle]
Chinese whispers!
Quote from: horse on March 23, 2008, 01:07:41 PM
Chinese whispers!
more like careless welding [rofl] [rofl] [rofl]
only kidding
[rofl] [rofl] [rofl]
See Chinese whispers strike again! was nothing to do with welding! when I had fuel cap fitted to new tank the bolt holes had to be drilled into new filler neck. Now before fitting tank I thought I had cleaned all the aluminium fillings and swarf out off tank. It is now obvious that I had not done such a good job as I had thought. Apparently it doesn't take a piece off crap the size off Bismark to block injectors........................well u learn!
So at least I have a complete spare set off throttle bodies now out off this [rofl]
how did the metal get through the filter in the pump???
Quote from: Chrisblack10r on March 23, 2008, 01:37:17 PM
how did the metal get through the filter in the pump???
That was my question! but were not talking about metal bits you can see. It was very fine Ali powder....................
Quote from: horse on March 23, 2008, 01:57:41 PM
Quote from: Chrisblack10r on March 23, 2008, 01:37:17 PM
how did the metal get through the filter in the pump???
That was my question! but were not talking about metal bits you can see. It was very fine Ali powder....................
little bastard's lol
all's well that ends well
Thats shite luck horse :crybaby2: And your right it does not take alot We had a 250hp tractor seize on the dyno after a rebuild. Stripped it down and found a tiny (and i mean tiny) piece of rag/fluff blocking an oilway to a main bearing... Not good Glad it's sorted :icon_thumright:
glad you sorted mate, how about boring out the throttle bodys for more go go :lol:
Quote from: slapknacker on March 23, 2008, 07:33:44 PM
glad you sorted mate, how about boring out the throttle bodys for more go go :lol:
Yesterdays idea. These days they go for oval cross section to get a larger area and the correct airflow "shape" to go around the bend in the intake port
Quote from: slapknacker on March 23, 2008, 07:33:44 PM
glad you sorted mate, how about boring out the throttle bodys for more go go :lol:
Lets wait and see what new airbox, belmounts and Filter do first! oh and removal off secondary throttle and butterfly valves!
thumbu ohhhhh kaaaay sounds mint :lol:
Quote from: r1ninja on March 23, 2008, 07:38:27 PM
Quote from: slapknacker on March 23, 2008, 07:33:44 PM
glad you sorted mate, how about boring out the throttle bodys for more go go :lol:
Yesterdays idea. These days they go for oval cross section to get a larger area and the correct airflow "shape" to go around the bend in the intake port
So's the ovals mate...Yamaha have been doing that since the late 80's
Dave
Quote from: davemfox on March 23, 2008, 08:01:30 PM
Quote from: r1ninja on March 23, 2008, 07:38:27 PM
Quote from: slapknacker on March 23, 2008, 07:33:44 PM
glad you sorted mate, how about boring out the throttle bodys for more go go :lol:
Yesterdays idea. These days they go for oval cross section to get a larger area and the correct airflow "shape" to go around the bend in the intake port
So's the ovals mate...Yamaha have been doing that since the late 80's
Dave
Ok didn't know that, but no-ones come up with a better shape yet