ZX 10 R Forum

Bike Stuff => Two Wheel waffle for all => Topic started by: michael4012 on November 07, 2013, 05:19:33 AM

Title: 200mph Club
Post by: michael4012 on November 07, 2013, 05:19:33 AM
Is there anybody or lots of people in the 200mph club what mods have you done to achieve it? iv got an 08 10r what do i need to do too mine to get 200 out of her?
Title: Re: 200mph Club
Post by: chaospunx on November 07, 2013, 10:42:49 AM
A smaller rear sprocket and shit load more power why you want 200mph?
Title: Re: 200mph Club
Post by: michael4012 on November 07, 2013, 04:40:57 PM
Quote from: chaospunx on November 07, 2013, 10:42:49 AM
A smaller rear sprocket and shit load more power why you want 200mph?
I quite simply just want to go out to germany and get to 200 mph just for the buzz!! LOL
Title: Re: 200mph Club
Post by: chaospunx on November 07, 2013, 06:47:36 PM
Fair enough mate would say it will cost a fair bit to get a true 200mph ie gps logged not what the speedo is saying just as a guide I had my bike showing 190mph on robbosliding's charity trackday but the true speed logged by gps was 168mph but I am a big lad and create alot of drag ha ha
Title: Re: 200mph Club
Post by: zx10r-Alan on November 07, 2013, 11:00:41 PM
188 is the most i've done, the shift light coming on made me look at the speedo, so there was still a bit left. Not bad for a D7, uphill with a 17st rider.
Title: Re: 200mph Club
Post by: NinjaPaul on November 07, 2013, 11:44:44 PM
You're not gonna get 200mph out of an 08 ZX10R without pumping thousands of pounds worth of tuning into the engine or sticking a turbo on it. The most I've ever seen on the clock was 189mph coming back from Mugello in 2007. That was on a 2005 10R with a slip on pipe and standard gearing with an uncorrected speedo, ie it was probably closer to a true 170mph although the bike still felt like it had a little bit left to give if it wasn't for the speed limiter kicking in.
Title: Re: 200mph Club
Post by: michael4012 on November 08, 2013, 04:59:08 AM
Quote from: NinjaPaul on November 07, 2013, 11:44:44 PM
You're not gonna get 200mph out of an 08 ZX10R without pumping thousands of pounds worth of tuning into the engine or sticking a turbo on it. The most I've ever seen on the clock was 189mph coming back from Mugello in 2007. That was on a 2005 10R with a slip on pipe and standard gearing with an uncorrected speedo, ie it was probably closer to a true 170mph although the bike still felt like it had a little bit left to give if it wasn't for the speed limiter kicking in.

The speed limiter is something i want off but dont know how, im not sure if its a mechanical or electrical device but i need to find out how!
Title: Re: 200mph Club
Post by: HammyUK on November 08, 2013, 07:09:04 AM
There isn't a Speed limiter - the ECU stops the speedo at 189mph
You won't get 200 though without work. It's not so much more power but you will need to regear, go over to race fairings, mask a lot of stuff up, etc.
To put it into context - TWO took a Busa to Brunters and it took 3 days, over 100 runs and best part of £3k in plastic, sprockets, etc to hit 201.3mph.
And that was with a rolling start through the trap at almost 100mph.
Title: Re: 200mph Club
Post by: michael4012 on November 08, 2013, 09:18:22 PM
Ok so iv got PCV autotune & the O2 optimizer K&N filter Brisk racing plugs de catted headers & leo vince slip on, i weigh 11 stone and can tuck behind the fairing, iv got the sat nav on the bike that'll show true speed! so gearing has anybody had any experience with sprocket sizes is it better to change both or either one? I think im going to have a run or two to see where im at, mirrors off etc to start! Rubber im having those scrubs for practice but less sticky for the final run would be more beneficial i think? I need more info please?
Title: Re: 200mph Club
Post by: MR2Brett on November 08, 2013, 11:44:03 PM
I think you,ll struggle however if you want to know what sprockets to use look at www.gearingcommander.com enter your bikes details and it,ll do the rest for you just remember to change it to mph as it defaults to kph ( button at the top). You,d have drag, wind resistance and mass to take into consideration. Good luck but I think it,ll be a big ask of a standard engine.
Title: Re: 200mph Club
Post by: NinjaPaul on November 09, 2013, 12:11:53 AM
 :iamwithstupid:

Looking at that website you could add a fair bit of top speed over standard, but at what cost. Altering the gearing so radically would surely make the bike horrid to ride from what its normally like, and even then, there's absolutely no guarantee you'll get perfect conditions to attempt a high speed run.

You might get lucky, but more likely you'll end up cursing the bike for annoying the crap out of you.  :dontknow:
Title: Re: 200mph Club
Post by: michael4012 on November 10, 2013, 07:24:40 AM
Quote from: MR2Brett on November 08, 2013, 11:44:03 PM
I think you,ll struggle however if you want to know what sprockets to use look at www.gearingcommander.com enter your bikes details and it,ll do the rest for you just remember to change it to mph as it defaults to kph ( button at the top). You,d have drag, wind resistance and mass to take into consideration. Good luck but I think it,ll be a big ask of a standard engine.
Nice one mate thats just about all the info i need iv worked out + 1 front & either - 2 or 3 on the rear should do the job if there's enough stock power to get it there!
Title: Re: 200mph Club
Post by: michael4012 on November 10, 2013, 07:26:16 AM
Quote from: NinjaPaul on November 09, 2013, 12:11:53 AM
:iamwithstupid:

Looking at that website you could add a fair bit of top speed over standard, but at what cost. Altering the gearing so radically would surely make the bike horrid to ride from what its normally like, and even then, there's absolutely no guarantee you'll get perfect conditions to attempt a high speed run.

You might get lucky, but more likely you'll end up cursing the bike for annoying the crap out of you.  :dontknow:
LOL i agree its a tough call & i probably will get fucked off with the bike but the gearing im only altering for the project its easy changing sprockets!
Title: Re: 200mph Club
Post by: HammyUK on November 10, 2013, 11:45:52 AM
+1 on the front and -2/3 on the rear will leave you with the same gearing!
1 front tooth is roughly the same as 3 rear teeth.
Title: Re: 200mph Club
Post by: NinjaPaul on November 10, 2013, 02:29:16 PM
Quote from: HammyUK on November 10, 2013, 11:45:52 AM
+1 on the front and -2/3 on the rear will leave you with the same gearing!

How so?  :dontknow:
Title: Re: 200mph Club
Post by: michael4012 on November 10, 2013, 04:54:20 PM
Quote from: HammyUK on November 10, 2013, 11:45:52 AM
+1 on the front and -2/3 on the rear will leave you with the same gearing!
1 front tooth is roughly the same as 3 rear teeth.
you could just make the rear smaller but then you would have to reduce the length of chain by increasing the front & decreasing the rear you can keep the same length to a degree, the chain i have is up to about half adjustment so i can swap sprockets and use the same chain.
Title: Re: 200mph Club
Post by: HammyUK on November 10, 2013, 10:08:43 PM
Quote from: michael4012 on November 10, 2013, 04:54:20 PM
Quote from: HammyUK on November 10, 2013, 11:45:52 AM
+1 on the front and -2/3 on the rear will leave you with the same gearing!
1 front tooth is roughly the same as 3 rear teeth.
you could just make the rear smaller but then you would have to reduce the length of chain by increasing the front & decreasing the rear you can keep the same length to a degree, the chain i have is up to about half adjustment so i can swap sprockets and use the same chain.

If you add one tooth on the front and take 2/3 off the rear YOU WILL NOT CHANGE THE GEARING !!?

You have to do one or the other or both but in greater differences!
You are going to have alter your chain or modify the swing arm to allow a massive amount of adjustment.
Title: Re: 200mph Club
Post by: michael4012 on November 11, 2013, 05:19:33 AM
Hammy iv used this as a guide http://www.gearingcommander.com/ it is correct mate
Title: Re: 200mph Club
Post by: HammyUK on November 11, 2013, 07:48:20 AM
I know the site -I linked it here originally years ago!
You don't seem to get that front/rear together are not going to do much unless you go outside of the ratios.
17/41 is standard
16/41 is the same as 17/44
18/41 is the same as 17/38
The difference is in the chain length due to rear sprocket circumference.
The overall gearing in the above ratios won't affect your top speed though as it hasn't changed.
As an example - 16t front will take your top speed from an indicated 189 to 176. Fact - this was done at Brunters on a 10R.
A 44t rear made it 177. Basically the same.
You will want something like an 18t front AND the rear around 36/37 but you will have a huge loss in acceleration.

(http://i684.photobucket.com/albums/vv207/HammyUK/857788C8-CC07-43B3-9A19-F6DC217CB229-5655-000005C7FFBAED16_zps26197578.jpg)
Title: Re: 200mph Club
Post by: michael4012 on November 11, 2013, 09:23:28 PM
So + 1 front giving me 18t & 36-37t rear which is - 8 or 9 should do it then! The acceleration i don't really care about as im not restricted to a strip or runway & they'll be coming back off afterwards. 
Title: Re: 200mph Club
Post by: michael4012 on November 26, 2013, 12:54:33 PM
I'm in Germany over the Xmas & New Year break so hopefully I will get a suitable days weather for a crack at it everything I eed wlll be in the van
Title: Re: 200mph Club
Post by: Phil on December 01, 2013, 11:30:31 PM
200mph is a good target but finding somewhere to do it that is geared up with the right kit is your next problem. Straightliners run Top speed sessions at a couple of runways in the UK. They generaly run through a standing mile at all tracks and some will allow a 1.4 mile track. The timing gear is spot on and used for land speed events. As an example of how far out speedos can be I have run about 8 Hayabusas through the traps and all have indicated over 200mph on the clock only to record a true speed of between 182-189mph. My stock road bike runs through every time at 189.2 - 189.9mph on 155BHP so with the right gearing and a bit of fettling a good ZX10 should be able to get close to that.
If you're on Facebook look for straightliners and keep your eyes open for the top speed dates for next year. If anyone is interested I will post them on the forum when I get them through.
There are some noise limits though and I think 103dB is the limit but I will confirm this after the AGM in Feb 2014.
Title: Re: 200mph Club
Post by: michael4012 on December 04, 2013, 07:54:20 PM
Quote from: Phil on December 01, 2013, 11:30:31 PM
200mph is a good target but finding somewhere to do it that is geared up with the right kit is your next problem. Straightliners run Top speed sessions at a couple of runways in the UK. They generaly run through a standing mile at all tracks and some will allow a 1.4 mile track. The timing gear is spot on and used for land speed events. As an example of how far out speedos can be I have run about 8 Hayabusas through the traps and all have indicated over 200mph on the clock only to record a true speed of between 182-189mph. My stock road bike runs through every time at 189.2 - 189.9mph on 155BHP so with the right gearing and a bit of fettling a good ZX10 should be able to get close to that.
If you're on Facebook look for straightliners and keep your eyes open for the top speed dates for next year. If anyone is interested I will post them on the forum when I get them through.
There are some noise limits though and I think 103dB is the limit but I will confirm this after the AGM in Feb 2014.
Cheers Phil, im not on facebook but will have a look. I am going down to BMW &AUDI's test section it'll only be the weather that stops me having a fair chance i think. My sat nav will be the best timing speed recording i have i do know that at 170 on my speedo the sat nav was recording 161 after that i dont know till i get there. What info do you have with custom sprocket manufactures, iv got a + 1 front with a -2 rear but an having difficulty getting a -3 with people quoting there not made by any one!
Title: Re: 200mph Club
Post by: Phil on December 05, 2013, 09:24:53 AM
I get my sprockets from B&C, as far as I know they also supply blanks so if they can't machine the bolt holes and center for you it would give you an option if you know someone with a mill that could do it for you.
Be interesting to see how you get on. :icon_thumright:
Title: Re: 200mph Club
Post by: michael4012 on December 06, 2013, 06:17:49 PM
Quote from: Phil on December 05, 2013, 09:24:53 AM
I get my sprockets from B&C, as far as I know they also supply blanks so if they can't machine the bolt holes and center for you it would give you an option if you know someone with a mill that could do it for you.
Be interesting to see how you get on. :icon_thumright:

i had spoken to them but they made no mention of blanks i will have another chat with them!
Title: Re: 200mph Club
Post by: Phil on December 19, 2013, 07:27:28 PM
Here are the dates for top speed events run by 200mph, the events are run by Straightliners. The speeds are usualy measured over the standing mile as this seems to be the latest standard for both here and America. There is league table so those over 200 can see where they stand in the world rankings. Occasionaly there is enough braking distance to allow 1.4 miles.
Anyway, dates are :-

2014 200MPH and UK TIMING ASSOCIATION TOP SPEED DATES

17 March Top Speed Monday Elvington
5/6 April Woodbridge Suffolk Mile
14 April Top Speed Monday Elvington
17/18/ May Yorkshire Mile & British National Records
16 June Top Speed Monday Elvington
5 July Sculthorpe Norfolk Mile
22 July Top Speed Tuesday - Elvington
16/17 August Northern Speed Trials/Elvington World wheelie records
27/28 September Woodbridge Suffolk Mile
20 October Top Speed Monday - Elvington

There will be a Top Speed Championship in 2014 classes to be advised

They also have a facebok page https://www.facebook.com/twohundredmph?fref=ts

If you have any questions just ask and I'll come back with an answer.
Title: Re: 200mph Club
Post by: michael4012 on December 20, 2013, 06:03:26 PM
Phil many thanks mate itt would be rude for me not to get In haha.

I am out in Germany and had a silly couple of hours today but not being a sunday there was a too much traffic and it wasn't on a autobahn Suitable one I fancy to get her wide open but I made some maps to suit the colder weather I did get her Uup to 180 on the sat nav. My hopes are for this sunday when I will be on appropriate Autobahn.
Title: Re: 200mph Club
Post by: michael4012 on December 24, 2013, 07:38:47 AM
with the +1 front & -2 rear i couldn't get here to pull past the 180 which i got with standard sprocket sizes. I did a couple of runs with just the +1 front getting to 180 again without to much difficulty from the bike but road conditions and traffic played against me so it'll be a another crack after Xmas probably the weekend 28th-29th.
Title: Re: 200mph Club
Post by: michael4012 on December 31, 2013, 11:48:01 AM
The best GPS recording I got was 184 the speedo appeared to stop. At 189 this was with the -2 sprocket on the rear & the bike as standard ie mirrors indicators & number plate its also worth noting she got a double bubble screen IV got it recorded on cam showing the speedo & sat nav readings when home I will get put up on u tube and post the link! I'm happy with 184 on a road spec 08!
Title: Re: 200mph Club
Post by: michael4012 on January 15, 2014, 05:25:29 PM
I was wrong it actually achieved 185mph as recorded on the SAT NAV
Title: Re: 200mph Club
Post by: Phil on January 17, 2014, 08:44:40 AM
Good effort. Going fast is easy, to go faster is the hard part. Have you any plans for a faster future.
Title: Re: 200mph Club
Post by: michael4012 on January 18, 2014, 07:23:20 PM
Funny enough I'm back out at the end of febuary so I'll have removed the step got me some less sticky road tyres and done something with the mirrors indicators & generally streamlined her a little who knows???
Title: Re: 200mph Club
Post by: NinjaPaul on January 19, 2014, 11:09:34 PM
I'll be pleasantly surprised if you manage to get much more out of it without more power but have fun trying, I know I would  :headbang:
Title: Re: 200mph Club
Post by: michael4012 on January 20, 2014, 10:45:30 AM
Haha I will surprised as well but its turned into how fast can it go. With a stockengine!! Ow yee its fun OK
Title: Re: 200mph Club
Post by: michael4012 on April 21, 2014, 04:19:40 PM
I was back out at the weekend with pig spotters fitted micro rear indicators & and a small number plate the road condition was much better as was the bike after being dynod at Steve Jordans, i got good breaks in the traffic but the wind was up but never being in a useful direction i only increased the previous 185 by 1 more :cry: however i will be back out in a few weeks & hopefully :-P   
Title: Re: 200mph Club
Post by: michael4012 on August 24, 2014, 06:04:05 AM
She did a new PB this morning of 187MPH with a side wind tomorrow's wind is looking favourable here's hoping
Title: Re: 200mph Club
Post by: NinjaPaul on August 24, 2014, 10:33:53 PM
Good effort.  :icon_thumright:
Title: Re: 200mph Club
Post by: michael4012 on August 25, 2014, 04:37:44 AM
Quote from: michael4012 on August 24, 2014, 06:04:05 AM
She did a new PB this morning of 187MPH with side wind tomorrow's wind is looking favourable here's hoping
It is on a stock road spec 08 with a modest 167BHP I think I'm going to put a race fairing on to see what difference it makes
Title: Re: 200mph Club
Post by: michael4012 on September 13, 2014, 03:09:34 PM
She's just done a 189MPH confirmed on the GPS but tomorrow mornings conditions look better so hopefully 190 is do able :-P
Title: Re: 200mph Club
Post by: michael4012 on September 13, 2014, 05:41:57 PM
Forget that last post she just did a 190MPH & the morning still needs to come [rofl]
Title: Re: 200mph Club
Post by: michael4012 on September 14, 2014, 07:48:33 AM
Holy fuck 192MPH for a stock engined road spec 08 Gen3 is mind blowing this weekend's success is purely down to RK Performance unbelievable
Title: Re: 200mph Club
Post by: michael4012 on September 15, 2014, 08:21:48 PM
Iv not been able to post this from my handheld until today
Title: Re: 200mph Club
Post by: MR2Brett on September 15, 2014, 08:52:54 PM
Well done, great effort. :hello2: :headbang:
What's your thoughts on How to get that extra 8mph???
Title: Re: 200mph Club
Post by: michael4012 on September 16, 2014, 07:27:00 AM
Quote from: MR2Brett on September 15, 2014, 08:52:54 PM
Well done, great effort. :hello2: :headbang:
What's your thoughts on How to get that extra 8mph???

Mmmmm without spending shit loads of money on more power I'm not sure yet possiblely aero dynamics can get extra but I reckon another 20BHP is needed :cry:
Title: Re: 200mph Club
Post by: michael4012 on September 17, 2014, 08:37:25 PM
Iv just uploaded this when the speedo maxis out at 189 you can see the rev counter continue to climb  https://www.youtube.com/watch?v=k5wiVovgDrQ
Title: Re: 200mph Club
Post by: michael4012 on September 27, 2014, 05:09:58 PM
Iv had time to think & I can't let this go this Gen3 has to do 200MPH+ I want to do it naturally so I'm looking to get the head worked & race cams in.
Title: Re: 200mph Club
Post by: MR2Brett on September 27, 2014, 08:37:31 PM
Quote from: michael4012 on September 27, 2014, 05:09:58 PM
Iv had time to think & I can't let this go this Gen3 has to do 200MPH+ I want to do it naturally so I'm looking to get the head worked & race cams in.
Where there's a will there's a way but you,ll need deep pockets me thinks. Got my ECU back from Rich yesterday (thanks Rich) so hoping to get it back to dynotech to see what improvements have been made (they dyno,d it 3 weeks ago so that,ll be the base figure).
Title: Re: 200mph Club
Post by: ZedThou on September 27, 2014, 11:37:32 PM
I think it would be cheaper to sell it and get a Gen4, even then I am not sure you will make it.  8mph is going to need quite a bit of extra power.  What about NOS.  A shot of NOS at around 190mph may do it, but again this won't be cheap.
Title: Re: 200mph Club
Post by: michael4012 on September 28, 2014, 07:16:49 AM
Quote from: ZedThou on September 27, 2014, 11:37:32 PM
I think it would be cheaper to sell it and get a Gen4, even then I am not sure you will make it.  8mph is going to need quite a bit of extra power.  What about NOS.  A shot of NOS at around 190mph may do it, but again this won't be cheap.
I reckon a Gen4 would top 200 without much more than flashing over the ECU it's far more aerodynamic than the Gen3 which I believe is the biggest problem here. I want to avoid turbo,s & nitrogen. To be honest if I had access to a Wind tunnel I would be developing a custom fairing rather than resorting to more horse power. Race fairings are designed for Racing not straight line speed & dimension wise the same as stock. BST wheels would make a difference but for the 2000 I can get the extra horses I need to break 200 :lol:
Title: Re: 200mph Club
Post by: davemfox on October 08, 2014, 10:49:19 PM
Quote from: michael4012 on September 15, 2014, 08:21:48 PM
Iv not been able to post this from my handheld until today

Nicely done  :icon_thumright: have a pony  :headbang:

Dave
Title: Re: 200mph Club
Post by: robbosliding on December 30, 2014, 04:33:39 PM
I got 189mph on a stock gen 3 ZX10R on a long straight at the Charity Airfield Riding Day that Chaos Punx was quoting. Couldn't break that number and that was stock gearing if I remember rightly.
Title: Re: 200mph Club
Post by: NinjaPaul on December 30, 2014, 06:26:50 PM
Quote from: robbosliding on December 30, 2014, 04:33:39 PM
I got 189mph on a stock gen 3 ZX10R on a long straight at the Charity Airfield Riding Day that Chaos Punx was quoting. Couldn't break that number and that was stock gearing if I remember rightly.

Assuming that was 100% stock and not fitted with a speedohealer then you wouldn't be able to go past 189mph as the clock stops there anyway. Realistically it was probably doing about 175ish.
Title: Re: 200mph Club
Post by: michael4012 on December 30, 2014, 10:05:04 PM
Quote from: robbosliding on December 30, 2014, 04:33:39 PM
I got 189mph on a stock gen 3 ZX10R on a long straight at the Charity Airfield Riding Day that Chaos Punx was quoting. Couldn't break that number and that was stock gearing if I remember rightly.
IIRC with the factory rev limiter at 12,500 the gen3 is geared to 182mph stock, obviously raising the limiter & or sprocket changes even tyre profile changes such as 200/55/ make a difference if the motor has the power to pull the extra gearing. Mine is nearly finished being built, iv gone for a +2mm bore ported head larger valves kent cams, JE high compression pistons lightened balanced & knife edged crank ceramic transmission bearings & more.
Title: Re: 200mph Club
Post by: michael4012 on December 30, 2014, 10:07:04 PM
& dont forget superb dyno set up by Rich down at RK performance(also a gold mine of info & contacts for this type of build)
Title: Re: 200mph Club
Post by: ZX10Rich on January 17, 2015, 11:47:01 PM
Quote from: michael4012 on December 30, 2014, 10:07:04 PM
& dont forget superb dyno set up by Rich down at RK performance(also a gold mine of info & contacts for this type of build)

Thanks for the positive feedback always nice to hear, looking forward to getting your bike back on the dyno and squeezing out those extra horses.
Title: Re: 200mph Club
Post by: michael4012 on January 18, 2015, 06:26:15 AM
The engine is all finished & ready fit but as my skills & knowledge have improved iv learned to check the valve to piston clearance by pressing the valve down whilst reading a dial gauge so im waiting on a another gasket coming from the US  :icon_thumright:  & then i will be asking you to run her in on the dyno :-P
Title: Re: 200mph Club
Post by: ZedThou on January 18, 2015, 10:07:53 AM
Looking forward to seeing the results on the dyno
Title: Re: 200mph Club
Post by: michael4012 on January 18, 2015, 10:19:54 AM
Quote from: ZedThou on January 18, 2015, 10:07:53 AM
Looking forward to seeing the results on the dyno
If i get + 25BHP then i will be very happy :icon_thumright: That would be 195 on the wheel :-P
Title: Re: 200mph Club
Post by: ZX10Rich on January 18, 2015, 10:32:50 AM
Quote from: michael4012 on January 18, 2015, 10:19:54 AM
Quote from: ZedThou on January 18, 2015, 10:07:53 AM
Looking forward to seeing the results on the dyno
If i get + 25BHP then i will be very happy :icon_thumright: That would be 195 on the wheel :-P

If you get that I will be very happy, I don't think its going to be that much but would like to be proved wrong, aim for a small number then anything above will make you happy lol, torque should show a big leap though. Either way its going to be a great motor.
Title: Re: 200mph Club
Post by: Chappo on January 18, 2015, 05:34:24 PM
Watching this with an eagle eye, good luck guys hope you get there  :icon_thumright:
Title: Re: 200mph Club
Post by: michael4012 on January 18, 2015, 05:47:00 PM
Quote from: ZX10Rich on January 18, 2015, 10:32:50 AM
Quote from: michael4012 on January 18, 2015, 10:19:54 AM
Quote from: ZedThou on January 18, 2015, 10:07:53 AM
Looking forward to seeing the results on the dyno
If i get + 25BHP then i will be very happy :icon_thumright: That would be 195 on the wheel :-P
How about a little bet Richard.......i propose if i get +25BHP or more you give me the Dyno time for free if it doesn't produce +25 BHP i forfeit my members discount  :occasion14::occasion14:  & pay full dyno rates

If you get that I will be very happy, I don't think its going to be that much but would like to be proved wrong, aim for a small number then anything above will make you happy lol, torque should show a big leap though. Either way its going to be a great motor.
Title: Re: 200mph Club
Post by: ZX10Rich on January 18, 2015, 06:16:29 PM
Quote from: michael4012 on January 18, 2015, 05:47:00 PM
Quote from: ZX10Rich on January 18, 2015, 10:32:50 AM
Quote from: michael4012 on January 18, 2015, 10:19:54 AM
Quote from: ZedThou on January 18, 2015, 10:07:53 AM
Looking forward to seeing the results on the dyno
If i get + 25BHP then i will be very happy :icon_thumright: That would be 195 on the wheel :-P
How about a little bet Richard.......i propose if i get +25BHP or more you give me the Dyno time for free if it doesn't produce +25 BHP i forfeit my members discount  :occasion14::occasion14:  & pay full dyno rates

If you get that I will be very happy, I don't think its going to be that much but would like to be proved wrong, aim for a small number then anything above will make you happy lol, torque should show a big leap though. Either way its going to be a great motor.

lol if it gets close to making 25 extra I'm sure i can make it read less on the dyno ( heat the dyno room, let some air out the tyres, or just do you a print out of someone else bike) mmm sounds like a deal lol
To be honest mate i would love to see it make 25 extra but thats a big ask, I'm sure it will be a absolute animal and a totally different bike but how a bike performs on the dyno isn't the whole truth as you found out with the ecu and full maps, not a massive difference on the dyno but big difference on the road, that 25 extra on the dyno would be insane difference on the road, I'm going to say 10-18 extra although you have got a nice cold winter on your side now for a few extra ponys.
Title: Re: 200mph Club
Post by: michael4012 on January 18, 2015, 06:41:01 PM
Quote from: ZX10Rich on January 18, 2015, 06:16:29 PM
Quote from: michael4012 on January 18, 2015, 05:47:00 PM
Quote from: ZX10Rich on January 18, 2015, 10:32:50 AM
Quote from: michael4012 on January 18, 2015, 10:19:54 AM
Quote from: ZedThou on January 18, 2015, 10:07:53 AM
Looking forward to seeing the results on the dyno
If i get + 25BHP then i will be very happy :icon_thumright: That would be 195 on the wheel :-P
How about a little bet Richard.......i propose if i get +25BHP or more you give me the Dyno time for free if it doesn't produce +25 BHP i forfeit my members discount  :occasion14::occasion14:  & pay full dyno rates

If you get that I will be very happy, I don't think its going to be that much but would like to be proved wrong, aim for a small number then anything above will make you happy lol, torque should show a big leap though. Either way its going to be a great motor.

lol if it gets close to making 25 extra I'm sure i can make it read less on the dyno ( heat the dyno room, let some air out the tyres, or just do you a print out of someone else bike) mmm sounds like a deal lol
To be honest mate i would love to see it make 25 extra but thats a big ask, I'm sure it will be a absolute animal and a totally different bike but how a bike performs on the dyno isn't the whole truth as you found out with the ecu and full maps, not a massive difference on the dyno but big difference on the road, that 25 extra on the dyno would be insane difference on the road, I'm going to say 10-18 extra although you have got a nice cold winter on your side now for a few extra ponys.
mmmmm i reckon i need independent witnesses anybody up for a cup of tea & bacon sarnie down at RK Performance one Saturday morning :glasses9: :glasses9:
Title: Re: 200mph Club
Post by: MR2Brett on January 19, 2015, 08:17:59 PM
If it were closer I'd be there! Looking forward to seeing the results. [clap]
Title: Re: 200mph Club
Post by: michael4012 on February 04, 2015, 02:45:19 PM
Right then, Saturday finally after delay after delay, the crankcase had been delayed by 3 weeks the head  by 2 weeks, & then the gasket was 2 weeks late which turned out to be the wrong one so took another fortnight. Dealing with all these folks over in the US wasn't easy. So previously my lovely with a flash K&N race filter simmi system gave 169.31 BHP & 77.69 torque going back on the same dyno at ZX10Rich business RK Performance with a +2mm bore, properly ported head, re-machined for +1mm valves, JE High Compression Pistons, lightened balanced & knife edged crankshaft, balanced rods, Kent Cams, Arrow full system, all new big & little end shells & main journal shells, ceramic transmission bearings. I was being cautious with a standard depth head gasket & stock timing rather than dialling the cams in for now with the plan to break her in on dyno using the motoman method. Rich did this then we changed the oil to a semi so rich could get on & re-map her so she then made a credible 195.48 with an extra 8 torque :shock: I could not be happier knowing that in 500 miles I would remove the head to check the bore & then drop the head & dial in the cams I believe 200BHP Is possible. A true 25BHP to date on a new engine is remarkable. When some of you have posted I will write the rest of the story.
Title: Re: 200mph Club
Post by: michael4012 on February 04, 2015, 07:33:18 PM
Right then, Saturday finally after delay after delay, the crankcase had been delayed by 3 weeks the head  by 2 weeks, & then the gasket was 2 weeks late which turned out to be the wrong one so took another fortnight. Dealing with all these folks over in the US wasn't easy. So previously my lovely with a flash K&N race filter simmi system gave 169.31 BHP & 77.69 torque going back on the same dyno at ZX10Rich business RK Performance with a +2mm bore, properly ported head, re-machined for +1mm valves, JE High Compression Pistons, lightened balanced & knife edged crankshaft, balanced rods, Kent Cams, Arrow full system, all new big & little end shells & main journal shells, ceramic transmission bearings. I was being cautious with a standard depth head gasket & stock timing rather than dialling the cams in for now with the plan to break her in on dyno using the motoman method. Rich did this then we changed the oil to a semi so rich could get on & re-map her so she then made a credible 195.48 with an extra 8 torque :shock: I could not be happier knowing that in 500 miles I would remove the head to check the bore & then drop the head & dial in the cams I believe 200BHP Is possible. A true 25BHP to date on a new engine is remarkable. When some of you have posted I will write the rest of the story.
Title: Re: 200mph Club
Post by: ZedThou on February 05, 2015, 09:15:54 PM
Well done, very impressive, all credit to for coming back from your previous disaster and getting such impressive figures from a Gen 3.  Look forward to seeing the final figures after it is all dialled in.  What's the torque output?  I won't ask what it's cost as I think it might give me nightmares
Title: Re: 200mph Club
Post by: michael4012 on February 06, 2015, 06:17:41 AM
Quote from: ZedThou on February 05, 2015, 09:15:54 PM
Well done, very impressive, all credit to for coming back from your previous disaster and getting such impressive figures from a Gen 3.  Look forward to seeing the final figures after it is all dialled in.  What's the torque output?  I won't ask what it's cost as I think it might give me nightmares
Thanks Zed the torque is upto a usable 85.15 :icon_thumright: Cost in total including sealants oil's gaskets & some extra tools (clutch holder, generator removal tool etc) shipping costs added up as well with import duties. Total Ã,£3600.00 including the Arrow full system. There is a need to mention how much the free advice & guidance from ZX10Rich would have cost :shock: He even called me at 10pm one night when i was struggling [clap] [clap] [clap] But the man is truly passionate about what he does :icon_thumright:
Title: Re: 200mph Club
Post by: MR2Brett on February 06, 2015, 11:22:12 AM
Well done [clap] [clap] [clap]
Great figures especially the torque, it must pull and pull and pull!!!
Looking forward to the overall results.
When's your next attempt to do the 200mph you set out for?
Title: Re: 200mph Club
Post by: ukzx10r on December 28, 2015, 09:01:06 AM
I had lower gearing on my gen 1 and downhill it just went over the 199mph limit on the clocks.
That said to do that you need a long wide open straight road which means you dont get much sensation of speed other than the wind.
Infact its a little boring.
The main reason im not a fan of silverstone!