News:

Welcome ZX10R Ninja Owners!!!!!
Front Page Here
Can all new members that haven't posted please read the admin and announcement page for the forum rules.

Main Menu

gi pro / pc111

Started by jeffoboyo1, May 29, 2012, 09:15:09 PM

Previous topic - Next topic

jeffoboyo1

hi guys since i fitted the power commander 111 to the bike my gi pro gets confused some times and dont know what gear im in , dont do it all the time but sometimes it flicks from 1 gear to the other. anyone else had this problem !!!!!!!!!!!!!! :roll:

jeffoboyo1


Kaos Theory

Did you re-teach the GI Pro the gears after you installed the PC III?

NellyB

#3
Interesting i was about to refit my GI pro to my new 04 10r which has a power commander. Does the wiring instructions still apply?
I would try the re- teach too

I thought Chicken strips were meant for restaurants

jeffoboyo1

hi guys no havent touched the gi since the pc been fitted, how do i re-teach the gi ??

billy

Exact same problem on my 1st gen.  Did Brands on Tuesday and it was always slow to react - in fact it was as much use as a chocolate teapot.  Has it set up with my PCIII by MSS so it should be all OK.  Just emailed manufacturer direct - if anything of use comes back I'll post up the reply.  Damn it was frustrating!!!!!!!!! [wall]

Kaos Theory

Quote from: jeffoboyo1 on May 31, 2012, 04:37:17 PM
hi guys no havent touched the gi since the pc been fitted, how do i re-teach the gi ??
From http://www.healtech-electronics.com/

First you'll need to reset the unit:
Cut  off  the  power of the unit 6 times in a row, while the GIpro display is
counting up and shows 3, 4 or 5 (or counting down and shows 2, 3 or 4).
On  certain bikes, you can power on/off the display by flipping the engine RUN
switch on/off.
Otherwise, you can do this by cycling the ignition key, or disconnectingreconnecting the GIpro coupler while ignition is on.
Note:  if  you  wish  to  stay  in  Custom mode but want to repeat the learning
procedure, you need to execute the Reset procedure twice.

Turn ignition On. The display counts backwards (6 to 1) indicating that
the unit is in Custom mode and it is ready to learn the gear positions.
- Raise the rear wheel off the ground by using a stand, and start the
engine in Neutral.
- The display will blink “1”.
Select first gear, release the clutch, and keep the RPM above idle speed.
The display is blinking faster while the unit is learning the gear.
- When the display shows “2”, select second gear.
Repeat this process until all gears are thought (5 or 6).
If your bike has 5 gears, wait until “6” is blinking, then pull the clutch in
and turn ignition off.
If your bike has 6 gears, wait until “o” (over) is indicated.- 3 â€"
The unit is programmed and should indicate the gears correctly.
Now, when ignition is turned on, the display counts forward (1 to 6) indicating
that it is fully functional.

Hope that helps lad.

jeffoboyo1

kool and the gang, will have a go at that mate , have a pony for your trouble....  :icon_thumright:

jeffoboyo1

Quote from: jeffoboyo1 on June 01, 2012, 06:53:20 PM
kool and the gang, will have a go at that mate , have a pony for your trouble....  :icon_thumright:
give me that pony back  [rofl] [rofl]
didnt work , but i did remember when i fitted it that there was a reset button on the underside of the gi , so i pressed that in for few seconds and yeeeee haaaaa learn mode poped up........... so think it sorted now but to wet to go and try it on the road...

billy

From a chap called Norbert  @ Healtech, might offer some extra insight!:

Please go through this check list:


1) At first, please execute the Learning procedure with the bike on stand
and engine RUNNING.
Make sure you see the "U" flashing after selecting 6th gear.
For setup instructions, refer to chapter 5.3 of the Manual:
http://www.healtech-electronics.com/docs/GIpro-S0x_UsersGuide_en.pdf


2) Disconnect the connectors, and make sure all connector pins are in place
- not bent or pushed out of position.
Spray some contact cleaner, e.g. WD40 into the plugs.
Then reconnect and check whether all connectors are locked properly.


3) Re-route the GIpro harness on a different path, farther away from other
electric cables.


4) If you can not complete the Learning process, or some gears are still
indicated incorrectly, most likely your GP Sensor is failing.
If you have some basic electronic skills and have a voltmeter, I can send
instructions how to check your GP sensor.


Kind Regards,
/Norbert

healtech-electronics.com

jeffoboyo1

hi guys , yea i had a U pop up after 6th gear when i done mine........
went for a spin today and i was working fine now ,,,  :headbang: