ZX 10 R Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome ZX10R Ninja Owners!!!!!
Front Page Here
Can all new members that haven't posted please read the admin and announcement page for the forum rules.

Pages: [1]   Go Down

Author Topic: Siezed engine mounts!  (Read 1292 times)

john.658

  • Club Racer
  • ****
  • Personal BHP 20
  • Posts: 774
  • Susan Boyle rocks!!!!!!!
Siezed engine mounts!
« on: December 12, 2009, 08:31:09 PM »

Anyone used a tap or heli coil to rethread summit. Having a bit of a problem with engine mounts on a trials bike, the bolts have become one with the frame!  [wall]
The heads both sheard off so I did all the usual stuff, loose oil, applied heat and vice grips etc and they aint moving!
 Looks like they will need to be drilled out but there is no room in the frame to drill straight so the remaining hole will be at an angle and a bit oval shaped.
 The frame is stainless steel, will a tap cut a new thread or will the frame be too hard? Would a heli coil or similar be a better option?
Any thoughts? 
Cheers.  :icon_thumright:
Logged

ZX10R-RACER

  • GP Hero
  • ******
  • Personal BHP 51
  • Posts: 2724
Re: Siezed engine mounts!
« Reply #1 on: December 12, 2009, 08:52:05 PM »

what bike is it?
Logged

john.658

  • Club Racer
  • ****
  • Personal BHP 20
  • Posts: 774
  • Susan Boyle rocks!!!!!!!
Re: Siezed engine mounts!
« Reply #2 on: December 12, 2009, 08:59:56 PM »

Hi,
It's a Sherco 250 trials bike. Upper engine bracket fixings that face inwards,  inside frame clearance is about 6-8 inches. The fixings have been welded flush into the frame, so burning them off and welding new ones may be an option, but it'll need stripped right down to the bare frame for that. Want to avoid that if poss, but I think the frame metal will be too hard for tapping a new thread but don't know much about it as I've never done it.
What ya reckon?
Logged

Andy J

  • RIP - Keiron
  • Super Moderator *VIP*
  • GP Hero
  • ******
  • Personal BHP 600
  • Posts: 16721
  • Near Chester - NorthWales
Re: Siezed engine mounts!
« Reply #3 on: December 12, 2009, 09:34:46 PM »

John,  if it were me I'd pop along to a local engineering company for them to sort it for me rathr than fight with it   :icon_thumright:
Logged

john.658

  • Club Racer
  • ****
  • Personal BHP 20
  • Posts: 774
  • Susan Boyle rocks!!!!!!!
Re: Siezed engine mounts!
« Reply #4 on: December 12, 2009, 09:38:16 PM »

You're probably right Andy, I've already gone 10 rounds with it and I'm way behind on points, 2lb mash hammer in tool box keeps catching my eye.  :boxing:
Logged

Andy J

  • RIP - Keiron
  • Super Moderator *VIP*
  • GP Hero
  • ******
  • Personal BHP 600
  • Posts: 16721
  • Near Chester - NorthWales
Re: Siezed engine mounts!
« Reply #5 on: December 12, 2009, 09:39:35 PM »

sometimes it's just best to take it to the experts before you make a mess of it   :icon_thumright:
Logged

chriszx10r

  • Rookie Racer
  • ***
  • Personal BHP 57
  • Posts: 689
  • Wrexham , North Wales.
Re: Siezed engine mounts!
« Reply #6 on: December 13, 2009, 12:39:35 AM »

sometimes it's just best to take it to the experts before you make a mess of it   :icon_thumright:

 :iamwithstupid:            I agree.       :emb:      :roll:
Logged
Pages: [1]   Go Up
 

Page created in 0.152 seconds with 22 queries.